Featured
-
China Wholesale Milling Cutter Grinding Machine Suppliers - End Milling for Aluminum HSS Milling Cutter for Aluminum 6mm – 20mm – MeiWha
Titanium aluminum nitride (AlTiN or TiAlN) coatings are slippery enough to help keep chips moving, especially if you aren’t using coolant. This coating is often used on carbide tooling. If you’re using high-speed steel (HSS) tooling, look for coatings like titanium carbo-nitride (TiCN). That way you get the lubricity needed for aluminum, but you can spend a little less cash than on carbide. Aluminum milling cutter: The main features of aluminum alloy spiral milling cutter are that it has an u... -
China Wholesale Sharpener Mill End Factories - Flat End Milling HSS Flat End Mills 6mm – 20mm – MeiWha
Center cutting end mills can be used for plunging operations (axial milling), and can also be used in side milling operations (radial milling). Non-center cutting end mills may only be used in side milling applications. The most common material used for end mills is tungsten carbide, but HSS (high speed steel) and Cobalt (high speed steel with cobalt as an alloy) are also available. Flat end mills are used for roughing operations, cutting 2D shapes like engravings and circuit boards, and fla... -
China Wholesale HSS Hand Thread Taps Manufacturers - Straight Flute Tap – MeiWha
Straight Flute Taps are used to cut threads in blind or through holes in most materials. They are manufactured to ISO529 standard and are suitable for hand or machine cutting. This versatile set contains three taps: - Taper Cut (First tap) – Used for through holes or as a starter tap. - Second Tap (Plug) – To follow the taper when tapping blind holes. - Bottom Tap (Bottom) – For threading to the bottom of a blind hole. All taps should be used with the corresponding drill siz... -
China Wholesale Milling Cutters Manufacturers - Ball End Milling HSS ROUGHING END MILLS 6MM – 20MM – MeiWha
They are available in a wide variety of diameter sizes from 1mm to 20mm. Meihua milling cutter 55 degrees: MW7050 series, coating color: fuchsia, Balzers coating, Jinlu GU25UF Bar stock, mold steel, stainless steel, general series of materials below 55 degrees, SKD11 corresponds to Chinese grades: Cr12MoV, 718 (41~47HRC hardness), NAK80 (HRC37~43), S316, Cr12MoV, C45, P20, ordinary mold steel, gray Cast iron, etc. Meihua milling cutter 65 degrees: MW7060 high hardness series, coating color: b... -
China Wholesale 1604 R8 Inserts Suppliers - For Heat-Resistant Alloy – MeiWha
As a full-line supplier of metalworking tools, MeiWha provides a full ISO range of quality tools. All standard geometries are supplied, including the most popular trigon shape. These semi-triangular turning inserts are used for axial and face turning and feature three 80° corner cutting edges on each side of the insert. They replace the rhombic inserts that had only two cutting edges, thus saving production time and cost while maximizing insert life. MeiWha offers a variety of unique chipform... -
China Wholesale Drilling And Tapping Machine Factories - Spiral Point Tap – MeiWha
The degree is better and can withstand greater cutting force. The effect of processing non-ferrous metals, stainless steel, and ferrous metals is very good, and the apex taps should be preferentially used for through-hole threads. Spiral point tap, also known as “gun taps” because they “shoot” chips forward (clever, huh?), are very effective at clearing chips ahead of the cutting edge of the tap and pushing them out the other end of the hole. This is especially effect... -
China Wholesale Bt-SLA Side Lock End Mill Holder Manufacturers - BT-SLA Side Lock End Mill Holder – MeiWha
BT-SLA Side Lock Holder is side-locking holder for holding shank of milling cutter, can be used for general milling, with screw holes on the side of the holder to clamp the milling cutter. Features : – For straight shank end mill. – End mill is held by two set screws. – End mill holder comes equipped with set screws. BT-SLA/SLN end mill holder with high precision BT30-SLA25 side lock end mill holder for lathe machine BT tooling is symmetrical about the spindle axis. This ... -
China Wholesale HSS Twisted Drill Bits Suppliers - Alloy Drill – MeiWha
Specially-designed flutes keep these bits centered as they drill, resulting in straighter, rounder holes with tighter tolerances. Made of solid carbide for the highest accuracy and longest tool life, they are harder, stronger, and more wear resistant than high-speed steel, cobalt steel, and carbide-tipped bits. They retain a sharp, hard edge at high temperatures for the best performance on hard and abrasive material. These bits require rigid toolholding to prevent breakage and should not be u... -
China Wholesale HSS Twist Drill Factories - HSS Drill – MeiWha
Meiwha Drill Tools offer HSS Drill and Alloy Drill.The HSS Twist Drill Bit Ground is for drilling through metal with maximum precision. The bit’s exposed 135-degree self-centring split-point tip combines active cutting and perfect centring without wandering, delivering maximum precision. The split-point tip also eliminates any need to pre-punch or pilot drill for up to 10 mm. This precision-ground bit made of HSS (high-speed steel) enables up to 40% faster drilling rate and up to 50% lo... -
China Wholesale CNC Tap Sharpener Factories - Straight Flute Tap – MeiWha
Straight Flute Taps are used to cut threads in blind or through holes in most materials. They are manufactured to ISO529 standard and are suitable for hand or machine cutting. This versatile set contains three taps: - Taper Cut (First tap) – Used for through holes or as a starter tap. - Second Tap (Plug) – To follow the taper when tapping blind holes. - Bottom Tap (Bottom) – For threading to the bottom of a blind hole. All taps should be used with the corresponding drill siz... -
China Wholesale NT-C Powerful Holder Factory - BT-HM Hydraulic Holder – MeiWha
There are three types of Meihua CNC BT tool holder: BT30 tool holder, BT40 tool holder, BT50 tool holder. The material: using titanium alloy 20CrMnTi, wear-resistant and durable. The hardness of the handle is 58-60 degrees, the accuracy is 0.002mm to 0.005mm, the clamping is tight, and the stability is high. Features: Good rigidity, high hardness, carbonitriding treatment, wear resistance and durability. High precision, good dynamic balance performance and strong stability. The BT tool holder... -
China Wholesale 400R 1604 Inserts Factory - PCD – MeiWha
As a full-line supplier of metalworking tools, MeiWha provides a full ISO range of quality tools. All standard geometries are supplied, including the most popular trigon shape. These semi-triangular turning inserts are used for axial and face turning and feature three 80° corner cutting edges on each side of the insert. They replace the rhombic inserts that had only two cutting edges, thus saving production time and cost while maximizing insert life. MeiWha offers a variety of unique chipform...
